- E*thirteen freehub bodies feature 6 degree (60 Point) engagement - Kits include freehub body, bearings, springs, and pawls - SRAM XD-11 Freehub body converts all e*thirteen plus level hubs for use with SRAM XD-11 drivetrains
Wheel Freehub Kit—XDR Driver Body Kit—Zipp ZR1 Compatible With: WH-202-FTLD-A1, WH-303-F650-A1, WH-303-FTLD-A1, WH-303-FTLR-A1, WH-303-FTUD-A1, WH-303-FTUR-A1, WH-404-FTLD-A1, WH-404-FTLD-B1, WH-404-FTLR-A1, WH-808-FTLD-A1, WH-808-FTLR-A1, WH-SP9-TLD-A1, WH-SP9-TUD-A2, WH-SP9-TUR-A2
The Wolf Tooth Rear Axle uses a captive steel washer under the head to reduce friction on the dropout face. This protects your expensive frame, transfers more of the tightening torque to clamping load for a stiffer interface and prevents the axle from sticking or galling when you want to remove it. - Made in Minnesota to aerospace standards
Stainless spoke nipple flat washers from Whisky. - .3mm Thickness
$4.00 - $17.00
Whisky Parts Co. Tubeless Rim Tape.
$9.00 - $53.00
Whisky’s tubeless rim tape is designed to make setup as easy as possible. Elasticity allows for smooth, even adherence while translucency lets you see where the tape contacts the rim. Different widths available to fit almost any rim.
$99.95 - $114.95
Built for bashing, whether on a gravity shred sled or fully loaded bikepacking rig, WTB's KOM Tough rims are extruded from top-tier alloy to provide utmost durability at a reasonable weight. Their legendary I-Beam construction has evolved to further reinforce the rim with dual support beams that provide increased strength and stiffness for the world's most aggressive riders. KOM Tough rims are proven on the toughest tracks of the Enduro World Series, depended on for daily trail rides, and trusted while bikepacking in remote regions of the world. Features: - TCS 2.0 creates a more robust, easily installed and dependable tubeless system. - A recessed channel along the center of TCS 2.0 rims allows installation of the all-new Solid Strip, which prevents tubeless tape from sagging at the spoke holes and results in a smooth, consistent interface between the tire and rim. - 4D angled spoke drilling eliminates binding and lateral loading, and disperses tension more evenly over a greater area.
$14.95 - $79.95
Make your WTB rims air tight and ready for tubeless use with WTB's TCS Rim Tape. This tape covers the spoke holes and can be used as a lightweight rim tape in any rim. Available in 11-meter (covers 5 rims) and 55-meter rolls (covers 27 rims).
$149.99 - $159.99
The Rampage rear wheel rolls on a four-bearing sealed freecoaster hub with 14mm chromoly axle. It's hand-laced to a 36-hole Rampage double-wall rim, and features a 9T chromoly driver with 3-pawl system. - Axle: 14mm chromoly (heat-treated) - Driver: 1-pc chromoly RHD or LHD - Hardware: Steel(17mm wheel nuts) - Hub shell bearings: 6002 (x1) & 7902 (x1) verify bearing number on side of rubber seal - Drilling: 36H - Weight: 46.4-ounces
Stan's lightweight aluminum valve stems are half the weight of Stan's standard brass valves. The secure round base is compatible with most tubeless rims and a perfect fit for all Stan's BST rims. A removable valve core makes adding sealant easy, and these babies fit up to 8mm valve hole. Sold as a pair.
Stan’s S1 wheelset line brings patented tubeless technology to an even wider range of riders. Built for long life, low maintenance, and outstanding value, the S1 series wheels feature 6061 series alloy rims and are available in six different widths suited to a wide range of tire sizes and riding styles. With an emphasis on value and durability, the S1 alloy wheelsets join a mountain wheel line-up that currently includes Stan’s successful MK3 premium alloy wheels and innovative Valor and Bravo carbon series wheelsets. While MK3 wheelsets are built to balance strength, light weight, and stiffness, S1 wheelsets focus on maximum strength and durability. The deeper profile and thicker walls of the S1 rims result in a 50-70g weight increase over MK3 rims, but offer greater impact strength for an even wider range of use. “The new S1 series wheels were developed from rims ridden in Redbull Rampage and raced on the World Cup DH circuit for years,” said Creative Director, Chris Currie. “The goal was to take everything we’ve done for tubeless technology, and put it into a truly bombproof and affordable wheel.” Designed according to Stan’s WideRight rim and tire fit system, S1 series wheelsets are available in six different rim models, with internal widths ranging from 23mm to 38mm. Combined with Stan’s low-profile, high-volume Bead Socket Technology rim design, these widths let the new S1 range accommodate tires from 2-inch to 3.5-inch. All S1 wheelsets are built with 32 spokes front and rear, Sapim’s proven Race spokes, Secure Lock brass nipples, and Stan’s faster-engaging Neo hubs. Hubs are available to fit most axle systems, including Boost. The S1 series includes reinforced versions of the classic Crest, Arch, and Flow--names already familiar to fans of Stan’s tubeless rims. In addition to the Crest S1, Arch S1, and Flow S1, three entirely new wider wheelsets will be available. The Sentry S1, Baron S1, and Major S1 bring Stan’s patented Bead Socket Technology to Plus bikes. Baron S1 Wheelset - Use: Plus Tire Performance, Adventure, and Trail - Internal Rim Width: 35mm - Optimal Tire Size: 2.8 to 3.2-inch - Hubs: Stan’s Neo 32-hole Front, 32-hole Rear - Spokes/Nipples: Sapim Race Black 2.0/1.8/2.0mm, Secure Lock - Brass Silver Nipples - Wheel Sizes and Weights: 26-inch (1,998g), 27.5-inch (2,060g), and 29-inch (2,162g)
- Asymmetric rim design allows for a stronger wheel while offering the easy inflation and Stan's trademark unmatched airtight seal. - 25mm width optimized for 40mm Gravel tires and up to 2.3'' mountain tires - Light and durable 6069 aluminum with welded joint and reinforced spoke bed
- Designed, tested, and raced to victories on the World Cup DH and Enduro World Series circuits - Tie beam triple-cavity rim design resists damage and prevents air loss under impacts - 29mm internal width optimized for 2.35" to 2.8" Trail, All-mountain, and DH tires - E-sync hubs Specs: - Wheel Tire Type: Tubeless Ready - Wheel-Brake Comp.: Disc IS 6-bolt - Rim Material: Aluminum - Spoke Type: Sapim D-Light - Valve: Presta - Rim Construction: Double wall
$20.00 - $22.00
Front end cap conversion kits for NoTubes Neo and Neo Ultimate - SealLock end caps feature a low friction U-cup seal that snaps into place
Stan's No Tubes' Presta Removable Valve Core is a replacement valve core for Stan's No Tubes Presta valve stems and Presta valve equipped rim strips.
$11.25 - $25.00
Can be used with Stan's ZTR rims to make them airtight or used as a lightweight rim tape in any rim. A single 10-yard roll will tape five 26-inch rims or four 29-inch rims or two wide road clincher rims. 21mm width fits: - ZTR Olympic - ZTR Iron Cross - ZTR 355 - ZTR Alpine - ZTR Crest - ZTR Alpha 340 (2 layers) - ZTR Alpha 400 (2 layers) - Most road clincher rims 25mm width fits: - ZTR 355 (26", 650b, 29") - ZTR Crest - Crest MK3 - ZTR Arch EX - ZTR Flow EX - Crest S1 27mm width fits: - ZTR Flow EX - ZTR Bravo - ZTR Hugo 52mm - Arch S1 - ZTR Rapid 28 - ZTR Rapid 30 - Arch MK3 30mm width fits: - ZTR Flow MK3
Stan's Threaded Valve Extenders let you convert deep-section rims to tubeless. They're precision-machined from aluminum and are designed to fit deep-dish carbon and aluminum rims. And, they're threaded on the outside so you can install the Presta lock-ring nut for a perfect seal.
This conversion kit allows you to use SRAM's 11-speed mountain cassette on your Stan's NoTubes wheels. Each kit includes an XD freehub, spacer, drive side end cap, and three sealed bearings.
$48.49 - $71.49
Sta Tru Front Wheel - Single Wall rim - Hub/Brake Compatibility: Rim Brake - Wheel Size: 20-inch - ISO Diameter: 406 / 20-inch BMX - Front Axle: 3/8-inch x 100mm - Valve: Schrader - Tire Type: Clincher
$51.49 - $77.49
Sta Tru Rear Wheels - Single Wall rim - Wheel Size: 20-inch - ISO Diameter: 406 / 20-inch BMX - Valve: Schrader - Tire Type: Clincher
- Taiwan 7x style 36 hole steel rim - Front steel hub uses a 3/8" flatted axle. Compatible with 5/16" forks - Steel wheels use C/N 14G UCP spokes w/ 5/8" brass nipples
$52.99 - $55.99
Sta-Tru Double Wall Front Wheels. - Hub/Brake Compatibility: Rim Brake - Wheel Size: 26-inch x 1 3/8 - ISO Diameter: 590 / 26 x 1 3/8-inch - Front Axle: 3/8-inch x 100mm - Valve: Schrader - Tire Type: Clincher
$56.00 - $77.49
- STW ST1 26.5mm wide alloy rims - KT QR ATB 9mm/100/108 axle - Black or Silver UCP spokes
$55.99 - $66.99
Sta Tru Front Wheel - Hub/Brake Compatibility: Rim Brake - Wheel Size: 27" - ISO Diameter: 630 / 27" - Tire Type: Clincher
$57.99 - $61.99
Sta Tru Rear Wheels - Hub/Brake Compatibility: Rim Brake - Wheel Size: 27" - Cassette Body Type: Threaded Standard 1.37" x 24tpi - ISO Diameter: 630 / 27" - Tire Type: Clincher
The Spank 359 Rim is a radially compliant gravity rim featuring our Oohbah Inverted Inner Wall and BeadBite anti-burp technology. Optimized for DH, FR, and heavy enduro use. - Moderately low 19mm profile height and wide width balances the benefits of radial compliance with high lateral stiffness and predictable handling. - Radial Compliance improves traction over bumps and chatter while reducing negative feedback to the rider. Performance and comfort are improved. - 5mm inner width is extremely versatile, fitting tires from 2.0" to 2.6", and even allowing + size tire use without negative squaring off of tire profiles. - Bead Bite tubeless hooks enhance tubeless performance and tire security, even at lower pressures.
SPANK Industries Fratelli Tape is a special ultra-light polyamide, adhesive tubeless conversion tape, which is ideal for SPANK's patented OohBah profile rims. Thicker, less pliable tapes are often difficult or impossible when taping complex rim profiles. Fratelli tape makes tubeless set up simple, and adapts well to a variety of rim types, including sleeved and welded joints. 25mm width tape is suggested for rims up to 29mm internal width, and 30mm tape for rims 30mm internal width and greater. With adhesive properties unaffected in a wide temperature range, Fratelli tape is also perfect for winter riders, or those in exceptionally hot environments. - Material: Ultra Thin Polyamide - Width: 25mm or 30mm - Features: high temperature range adhesive, ideal for complex rim profile Installation: - Affix tape all the way around on the right side snug against the bead hook - Then repeat a second circumference around the left side, providing double-thick coverage over the spoke holes - Use a red-hot awl or similar to pierce the valve hole
- Replacement rear wheel skewer. - Specifically designed for use with Saris trainers. - Can be used for both indoor and outdoor rides.
$1,599.00 - $2,199.00
EWS TESTED. The EWS is strict—break certain parts and you DNF. The rule's meant to encourage sensible management of equipment, but it's also tipped the balance in favor of toughness and reliability. Enter the Reserve 30. Its 30mm internal width supports a 2.3-2.5" tire, and the thick rim beads stand up to the abuse of tough, rocky, steep tracks ridden at elite speed. While DH rims see greater single impacts, nothing beats the full weekend of regular abuse that an EWS race dishes out, to say nothing of the infamous 'Anti-Grip' and the rocks buried within the moondust in the Andes of Chile.
The Deadbolt Ultralight Thru-Axles are offered in a 6mm flat button-head design, for a flush, clean look. Lightweight, easy to use, and secure. - CNC-machined from 7000 series aluminum - One-piece design - Designed to fit all current Salsa thru-axle frames - For other frames, check with the manufacturer for compatibility and other specifications - 6 mm hex wrench required for installation
Page 1 of 24 Next page