Parts & Accessories
Stan's lightweight aluminum valve stems are half the weight of Stan's standard brass valves. The secure round base is compatible with most tubeless rims and a perfect fit for all Stan's BST rims. A removable valve core makes adding sealant easy, and these babies fit up to 8mm valve hole. Sold as a pair.
$15.00 - $20.00
Stan's 3.30/3.30Ti Hub Kit converts Stan's 3.30 front hubs from quick-release to through-axle compatible. Installation is easy—just pull the old ones off and put the new ones on. Conversion kits available in 12mm and 15mm.
$11.25 - $25.00
Can be used with Stan's ZTR rims to make them airtight or used as a lightweight rim tape in any rim. A single 10-yard roll will tape five 26-inch rims or four 29-inch rims or two wide road clincher rims. 21mm width fits: - ZTR Olympic - ZTR Iron Cross - ZTR 355 - ZTR Alpine - ZTR Crest - ZTR Alpha 340 (2 layers) - ZTR Alpha 400 (2 layers) - Most road clincher rims 25mm width fits: - ZTR 355 (26", 650b, 29") - ZTR Crest - Crest MK3 - ZTR Arch EX - ZTR Flow EX - Crest S1 27mm width fits: - ZTR Flow EX - ZTR Bravo - ZTR Hugo 52mm - Arch S1 - ZTR Rapid 28 - ZTR Rapid 30 - Arch MK3 30mm width fits: - ZTR Flow MK3
$20.00 - $22.00
Front end cap conversion kits for NoTubes Neo and Neo Ultimate - SealLock end caps feature a low friction U-cup seal that snaps into place
Durasync freehub bodies feature triple freehub bearings for increased axle stability to handle even greater vertical and torsional loads. This CNC machined durasync freehub is a direct replacement for your Neo hub, and includes pawls, springs, pawl retaining ring, and red freehub spacer. Bearings are pre-installed. - 6-pawl system provides 36 points of contact and 10-degree engagement for quick acceleration - Chromed steel bearings - Wide bearing stance and axle design reduces flex and adds durability - Low drag main seal prevents contamination and reduces resistance - Mini Driver has a Shimano HG spline, but is 10mm shorter to accept 11-speed cassettes with 10t cogs from Hope and OneUp Components
$20.00 - $23.00
Rear end cap conversion kits for NoTubes Neo and Neo Ultimate hubs - SealLock end caps feature a low friction U-cup seal that snaps into place
Replacement Shimano/SRAM freehub body for Stan's NoTubes 3.30 rear hubs.
Front RockShox/SRAM-specific Torque-Cap 15mm through-axle SealLock end caps for Neo and Neo Ultimate hubs. SealLock end caps feature a low-friction U-cup seal that snaps into place and stays secure even when your wheel is removed from your bike. Torque-Cap end caps have the same 15mm inside diameter as other systems, but outside diameter is larger (31mm), making these end caps only compatible with Torque-Cap-compatible forks. Note: Torque caps are not compatible with centerlock hubs.
Use Stan's Tubeless Valve Stems when you're converting standard rims to tubeless via the taping method. These also have a removable core for easier application of tire sealant. Note: Schrader valve is for non-stepped Hugo rims. If your Hugo rim decal reads: - MAX RIM PRESSURE: 2.8 tires: 26psi, 3.0 tires: 24psi - ERD 615, 622x49.9, 29 in x 52.3mm Your rim has a stepped valve and is not compatible with this Schrader valve.
Stan's No Tubes' Presta Removable Valve Core is a replacement valve core for Stan's No Tubes Presta valve stems and Presta valve equipped rim strips.
This conversion kit allows you to use SRAM's 11-speed mountain cassette on your Stan's NoTubes wheels. Each kit includes an XD freehub, spacer, drive side end cap, and three sealed bearings.
Replacement bearings for Stan's NoTubes Neo hubs. Includes 2 bearings. - 26mm OD x 15mm ID - 7mm thick
Replacement springs and pawls. Includes 6 pawls, 6 springs and 1 plastic retaining ring that holds the pawls in place even during disassembly to ensure you're never searching the floor for tiny springs.
The same spoke thread treatment used by Stan's pro wheel builders is now available to everyone. Stan's SRD Spoke Powder fills the threads of the spoke and functions as both a lubricant during assembly and a thread lock once built. Each bottle contains 24g (.8oz) which will treat approximately 300 wheels. The PTFE powder in Stan's SRD Spoke Powder acts as a barrier, keeping the metal of the nipple from bonding to the metal of the spoke and preventing spoke wind up during build or adjustment. In promoting a smoother turning nipple, the powder also ensures more accurate and consistent wheel builds, with less “ping and pop" during and after the build. The powder also fills the threads of the spoke to act as a thread lock that prevents loosening and de-tensioning and is particularly well suited for mechanically locking nipples such as Sapim's Secure Lock. - Improves tension consistency and overall build quality - Prevents spoke wind up - Offers secure thread lock between spoke and nipple - Prevents corrosion between spoke and nipple - Can be used dry or as a slurry - Works great with mechanically locking nipples
Stan's Threaded Valve Extenders let you convert deep-section rims to tubeless. They're precision-machined from aluminum and are designed to fit deep-dish carbon and aluminum rims. And, they're threaded on the outside so you can install the Presta lock-ring nut for a perfect seal.
Page 1 of 1