Parts & Accessories
The Wahoo RPM cadence sensor is your sleek little solution for measuring cycling cadence data. It is wireless, magnet-less, lightweight, and easily mounts to your bike's crank arm or to your shoe. Bluetooth Smart and ANT+ dual band technology allows you to connect to and display data on both smartphones and GPS bike computers. Collecting cadence data has never been this easy. - Both ANT+ and Bluetooth Smart capabilities allow for a wireless connection to both smartphones and bike computers. - No tangled wires on your bike to connect the sensor to your device. - It only weighs 7 grams! - Provides accurate cadence data during your ride - (1) mount with double sided 3M tape, or (2) use the silicone sleeve and mount with zip ties. - The RPM can be worn on your shoe for spin classes or use with multiple bikes - Two LED lights show the sensor's device connection (blue) and cadence detection (red) - No charging required! Operates on a coin cell battery for up to 1 years. - RPM cadence sensor will fit with most bikes and frame sizes
The Skyliner is a front wheel support for use with Tacx classic trainers. It raises and supports the front wheel for a natural cycling position and increased stability. It also serves as a handle to carry the trainer.
A sweat cover with a pocket for your smartphone. The sweat cover protects your bike against perspiration and enables the use of a phone while training. The Tacx sweat cover is made from absorbent textile to catch and retain perspiration. Its clever design fits all bikes and enables easy mounting. Suitable for a variety of phone sizes - max. length 138mm, max. width 68mm.
The Tacx Sweat Cover protects your bike from corrosion caused by perspiration. It is made from absorbent textile to catch and retain perspiration. Its clever design fits all bikes and enables easy mounting.
$29.99 - $39.99
The E-Thru Trainer Axle allows the use of a mountain bike in a Tacx trainer. These axles are only suitable for Tacx classic trainers.
- Adapter for Tacx Direct Drive trainer - 01 is compatible with 142 x 12mm and 148 x 12mm - 02 is compatible with 135 x 10mm - 03 is compatible with 135 x 12mm (w/5 mm spacer included with every Tacx Direct Drive trainer), 142 x 12mm and 148 x 12mm - 04 The thru axle adapter kit is for bikes with a 12 mm thru axle. The axle adapter is required to couple the rear stay with the thru axle mount on a Tacx NEO or FLUX Smart trainer.
Look, your child is destined for greatness. We won't dispute that. But, why wait until they can walk for them to rock their awesomeness? If they're crawling, they're ready to explore the world. Attach the Strider Rocking Base to a Strider 12 Bike and get them rocking. The rocking base doesn't just familiarize them with a bike, the rocking motion helps develop their balance, spatial awareness, and core strength. No batteries. No annoying sounds. Just pure, rocking fun. - Compatible with the Strider 12 Classic, Sport, and Pro Balance Bikes - When the Strider 12" Bike is attached this product is intended for ages 6 months – 5 years old for Strider Sport and Pro, and ages 6 months – 3 years for Strider Classic.
The Saris Leveling Block keeps your bike level with your trainer. - Adds stability to your training ride. - For use with any rear wheel-mounted trainer. - Raises front bicycle tire 1.1 inches (2.8 cm) off the ground
Keeps corrosive sweat from reaching your frame. - Cell phone pouch included.
- Includes clutch knob and L-bolt - Basic Trainer Clutch Knob is compatible with any Wind, Mag, Mag+, Magneto or Fluid trainer that already uses L-bolt - Magnus Clutch Knob should only be used with Magnus Smart Trainer - Watch our video to learn more
BLE USB Adapter gives Rouvy virtual training software the ability to seamlessly connect to Bluetooth devices and sensors. The adapter contains a Bluetooth (BLE) radio that allows PCs to communicate with BLE devices, including Saris smart indoor bicycle trainers and power meters. Most importantly, the BLE USB Adapter is necessary to update the firmware Over the Air (OTA) via VirtualTraining for the Hammer and Magnus bike trainers. - Bluetooth adapter for PCs to work with Rouvy - Needed for Over the Air Firmware Updates to Smart Indoor Bike Trainers. - Works with PC desktops and laptops.
For a stable, worry-free ride with any rear wheel-mounted trainer. Product Features - For a stable, worry-free ride with any rear wheel-mounted trainer. - Unique 3-level design lets you select the level of difficulty. - Stack two blocks to simulate climbing workouts. Three different positions to raise your front wheel and simulate hill climbs - 2.1 inches (5.3 cm) - 2.7 inches (6.8 cm) - 3.1 inches (7.9 cm)
Adjust resistance on Mag trainer without leaving the saddle. - Quick Release mounting system fits most stems. - For use with the Mag bike trainer only
The Saris thru axle adapter is designed for indoor use on Saris- or CycleOps-branded trainers only and should not be ridden outdoors. - Compatible with Classic series trainers and most Pro series trainers. Not compatible with PowerSync trainers. Contact us with trainer compatibility questions. - This adapter is designed to work with bikes that have a 142x12mm thru axle with 1.0 or 1.75 thread pitch. - The axle is threaded on both sides to fit both Syntace and Maxle/ABP style thru axle systems. - Many bike manufacturers do not publish thread pitch or hub spacing online. If you are unclear as to what type of thru axle your bike uses, please reach out to your local bike shop or the bicycle manufacturer directly. What's Included - Thru axle - Washers - End caps with bolts
Connect your PC to CycleOps VirtualTraining.
Adapts a thru axle hub bike for a Saris bike trainer. - Trainer Thru Axle Adapter For Saris Trainers - Thread pitch: 1.00 & 1.75 What's Included: - Thru axle - Washers - Endcaps with bolts Trainer Compatibility The Saris Trainer Thru Axle Adapter is designed for indoor use on Saris trainers only and should not be ridden outdoors. Compatible with current basic trainers. Not compatible with CycleOps PowerSync trainers. Contact us with trainer compatibility questions. Bike Compatibility Many bike manufacturers do not publish thread pitch or hub spacing online. If you are unclear as to what type of thru axle your bike uses, please contact us.
The Saris thru axle adapter is designed for indoor use on Saris- and CycleOps-branded trainers only and should not be ridden outdoors. Compatible with current classic series trainers. Not compatible with the JetFluid Pro, SuperMagneto Pro, PowerBeam Pro, or PowerSync trainers. Contact us with trainer compatibility questions. - This adapter is designed to work with bikes that have a 142x12mm or 148x12mm thru axle with 1.0 or 1.75 thread pitch. - The axle is threaded on both sides to fit Syntace and Maxle/ABP style thru axle systems. - Many bike manufacturers do not publish thread pitch or hub spacing online. If you are unclear as to what type of thru axle your bike uses, please reach out to your local bike shop or the bicycle manufacturer directly. - Adapts a thru axle hub bike for a trainer - Only compatible with current basic trainers - Fits most 142-148mm thru axle bikes with 1.0 or 1.75 thread pitch
Everything you need for the best indoor trainer experience possible. - Can be used across a wide range of trainer setups. - Includes Trainer Mat, Climbing Block and Saris towel.
Trainer Mission Control Every training room needs a control center, and the TD1 is more than equipped for the job. Featuring built-in power strip with 2 AC and 2 USB outlets, this indoor trainer desk was designed to keep everything you need charged, organized and close at hand. Its roomy 12" x 20" table top is made from laminated birch for easy clean up, and is supported by stainless, corrosion-resistant steel sourced from America’s heartland. And as part of the Saris trainer eco-system, the TD1 is a perfect complement to the MP1 trainer platform. After just one ride with a dedicated trainer desk, you’ll ask yourself how you ever rode indoors without one. - Stay Charged: built-in power strip keeps training necessities nearby and powered up. - Pick Your Height: adjustable for wide range of bikes and training configurations. - Easy Cleaning: laminated birch wood top makes for easy clean-up post-ride. - Steamlined Look: built-in cable management and stainless steel hardware are both functional and eye-pleasing. - Enhanced Experience: a great addition to indoor training. Specs - Base: 13-inches wide x 36-inches Depth - Desk Top: : 12-inches Width x 20-inches Depth - Adjustable Desk Height from Floor: 40- to 55-inches - Materials: Laminated birch table top supported by a steel frame, featuring stainless steel and corrosion-resistant hardware - Cord Length: 6- foot AC cord - Built-in power strip with 2 AC and 2 USB outlets - Built-in cord retention clips for easy cable management and a clean look.
A League of Its Own Since their inception, bike trainers have set out to solve one problem: simulating outdoor riding, indoors. Then came smart trainers and indoor cycling apps, complete with virtual races, group rides and controlled workouts. Suddenly athletes across disciplines were eager to ride indoors. The indoor training renaissance isn’t over. To make the experience even better, and to harness all the benefits riding indoors has to offer, you need a way to stay comfortable and engaged. The MP1 Nfinity Side-to-side movement isn’t new, but it also doesn’t capture the natural movement you experience outdoors. The MP1 with Nfinity technology truly moves the way you do because it adds the fore/aft axis to the equation. The MP1 combines over 20 years of indoor training expertise to not only create the movement platform category – but to perfect it. The result is an unparalleled trainer platform that reimagines the indoor trainer experience altogether. Features Introducing Nfinity Technology In order to bring stationary cycling to life, the MP1 needed movement in multiple axes. The result is an innovative technology combining curves, axes, gravity physics and mechanical ingenuity. The MP1 is the only way to experience this revolutionary technology. Compatible with Nearly Any Bike Trainer If you can experience the freedom of movement indoors, then why limit access with trainer compatibility? We believe that anyone with a bike trainer that fits should be able to tap into the benefits of Saris Nfinity Technology via a ride on the MP1 – which is pretty much everyone. So grab your trainer and check our bike trainer fit guide. Increased Comfort Riding a bike indoors can be uncomfortable because your movement is typically limited by the trainer. Pressure mapping and motion capture technology shows the MP1 significantly alleviates saddle and foot pressure compared to riding a static trainer. Recruit More Muscles It’s true that adding your trainer of choice to the MP1 engages more muscles than a stationary ride. From engaging the upper body to get through sticky spots to activating smaller, key muscles to stay balanced, the MP1 is the only way to recruit large and small muscle groups while riding inside. Adjustable Touch Points The MP1 is compatible with a wide range of setups. Complete with adjustable touch points and well-placed grip tape, the MP1 platform can be used with nearly every indoor bike trainer and training footprint. Looks Good, Too The MP1 looks as good as it moves. The platform deck is made from beautiful birch, while steel sourced from America’s heartland ensures the MP1 can handle the hardest of efforts. For the most cohesive aesthetic, the MP1 is the cornerstone of the Saris trainer eco-system, complete with the trainer desk and smart trainer of choice. It’s Fun, Pure and Simple Our goal was to make the time spent indoors as enjoyable as possible. The movement platform not only enhances the virtual training experience, the MP1 with Nfinity Technology brings indoor training to life. - Nfinity Technology: revolutionary tech that brings movement indoors. - Movement for All: compatible with a variety of training configurations; bikes, desks and nearly every trainer available. - Trailblazing: the MP1 ushers in a type of riding never seen or felt before. - Pure Fun: a responsive, immersive and authentic training experience that’s anything but boring. - Get Comfortable: reduces pressure on touch points so you can put in the miles. - Eye-Catching: mix of steel, aluminum and birch compliment most training spaces. - Personalized Eco-System: put the MP1 at the center with your trainer of choice to create your ideal training station. Specs - Max Fore-Aft Travel: 9.5” - Max Side-to-Side Angle: 6° - Compatible with all major brands and models of bike trainers. - Materials: Steel, aluminum and birch - Weight: 62 lb - Dimensions: 6” tall x 63” long x 35.5” wide - Fully assembled in box - Grip tape strategically placed to assist in walking on the trainer platform. - Tested to the combined weight (rider, bike and trainer) of 350 lb. - Built-in front wheel block for road and MTB.
Our Trainer Axle is designed to adapt your thru-axle equipped bike to on-wheel trainers, such as a 1up, Blackburn, Cyclops, Kinetic, Tacx, Wahoo, and many others. Our goal is to fit the thru-axle to your bike perfectly to minimize spacers and extra parts, providing a clean, high-performance axle for your bike. Train, warm up, and be race ready and fit for the season. - When it’s time for your race or time to head outside, simply remove your bike from the trainer, remove the drive side axle end and go. Our axle is suitable for use on or off the trainer, indoors or out. - The axle shaft and axle ends are precision CNC-machined from 7075 aluminum and hard-anodized for rugged durability. - No special tools required. Design allows for installation or wheel removal using your standard 5mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world. Important: Before you order, make sure your specific trainer will accommodate the width of your modern thru-axle-equipped bike. Measure your trainer at the widest setting and measure the outside width of your bike frame. Our the trainer axle ends will extend past your frame on each side.
Our Trainer Axle is designed to adapt your Surly MDS/Gnot Boost thru-axle-equipped bike to on-wheel trainers, such as a 1up, Blackburn, Cyclops, Kinetic, Tacx, Wahoo, and many others. Our goal is to fit the thru-axle to your bike perfectly to minimize spacers and extra parts, providing a clean, high-performance axle for your bike. Train, warm up, and be race ready and fit for the season. - This axle is for Surly bikes with the MDS/Gnot Boost system. - When it’s time for your race or time to head outside, simply remove your bike from the trainer, remove the drive side axle end and go. Our axle is suitable for use on or off the trainer, indoors or out. - The axle shaft and axle ends are precision CNC-machined from 7075 aluminum, and hard-anodized for rugged durability. - No special tools required. Design allows for wheel installation or removal using your standard 5 mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world.
The TPH-1 Tablet Grip from Minoura is the ultimate tablet holder for indoor training. Fitting a diameter between 28mm and 35mm, this stand will fit most bicycles. - Perfect accessory to use with LiveTraining Apps, The Sufferfest videos, or other media - SM clamp easily mounts or dismounts from the handlebar or tube - Spring-loaded clamp system is simple to use and securely holds your device in place - Holds from a 7.9 to 9.7 inch screen with 360 degree rotation system - Can mount to your repair stand so you can easily reference the Internet when working on your bike
$18.00 - $20.00
- Replacement belt - Select model based on model/roller size and belt size
Of course you love your Omnium Trainer, but you’re left wondering how you could possibly love indoor cycling training even more. Easy, our absorbent Sweat Guard is designed to keep your carbon, aluminum and steel frame and components safe from corrosive sweat while mimicking your favorite spin class at home. And because your cycling training plan asks for incredibly intense efforts, the Sweat Guard ensures not a drop of sweat will hit your frame during leg-busting intervals. Add a Floor Mat to your indoor cycling collection and you’ve got a training party! - Ultra absorbent terry cloth material - Protects carbon, aluminum, and steel frames and components - Adjustable to fit most any bike - Simple setup and removal with Velcro handlebar mounts and elastic seatpost strap - Machine washable, cold
Of course you love your Omnium Trainer, but you’re left wondering how you could possibly love indoor cycling training even more. Easy, our non-slip and water-repellent (aka sweat) Floor Mat is designed to keep you safe and protect your floors while in your cycling cleats indoors. And because your cycling training plan asks for incredibly intense efforts, the Floor Mat can ensure firm contact with the ground and prevent movement during leg-busting intervals. Add a Sweat Guard to your indoor cycling collection and you’ve got a training party! - Non-slip surface keep you safe while in cycling cleats - Protects floors from sweat and bike grime - Water-repellent surface does what it was designed to do – keep sweat off your floor - Compress-ability ensures trainer stays put during intense efforts - Easily rolls up for storage - Cleans easily with soap and water - Absorbs noise and vibration - Enhances overall stability of any indoor trainer setup - 4mm (5/32?) thickness is optimal balance of support and storage
You’re already a proud owner of the Omnium Zero-Drive Bike Trainer, but today you’re looking for a sweat-inducing, intense workout. Designed to be lightweight and portable, the Omnium Trainer is adaptable to whatever bike you ride and whatever workout you’re targeting – let the Omnium Over-Drive Sled be your next training accessory. - Dynamic, free-floating rear wheel design promotes the most realistic riding experience of any stationary bike trainer - Patented, Internal Progressive Resistance via friction-less Eddy Current Technology - Parabolic, progressive resistance curve accurately simulates outdoor cycling (rolling + wind resistance) - Precision machined 4” aluminum rollers create a smooth and quiet ride - Adaptable to virtually any bike (up to 1348mm wheelbase with optional extender) - No tools required to assemble or store — simply unfold for use and fold for storage and travel - Maintenance-free resistance unit and roller bearings - Compatible with Zwift, The Sufferfest, TrainerRoad and Kinomap traditional trainer features* *Requires ANT+ or BT rear wheel speed sensor
The Gel Block is an indispensable accessory for perfecting your position on the bike and provides a more natural feel to your training. - Reduces vibrations on the handlebars for more comfortable training - Non-slip Elastogel insert ensures maximum stability and alignment of the front wheel - Suitable for road and MTB
This height-adjustable front wheel support can simulate both flat terrain and slopes perfectly - Unique design with 5 levels lets you adjust the height of your front wheel to simulate hill climbs up to 6% - Anti-slip rubber feet eliminate handlebar vibrations - Internal design that guarantees maximum wheel stability - Suitable for both road and MTB - You can attach to the trainer frame when not in use for easy transport and storage
The Elite Thru Axle adapter kit makes Elite trainers compatible with bicycles with 10mm to 12mm diameter through bolts on the rear wheel (lengths from 130mm to 148mm boost). Easy to set up to start right away with your training, this Thru Axle adapter is made from quality material to ensure an immediate setup and great protection to the threads of your bicycle frame. This unit does it all!
Page 1 of 2 Next page